Floor Space Ratio (FSR) Explained: How Much Can You Build on Your Block in Sydney?

Floor space ratio caps how much floor area you can build compared with your lot size. Here is how it works and how to check yours.

What is floor space ratio? The quick answer

Floor space ratio (FSR) is the total floor area of a building compared with the area of the lot. A higher ratio allows more floor area.

It is a ceiling, not a promise. Height, setbacks, site coverage and other controls may stop you reaching it.

Quick answer

Multiply your lot area by the FSR to get the maximum gross floor area. Then check whether other controls limit you further.

  • FSR counts floor area across all levels, not just the footprint
  • It comes from the local environmental plan, where one applies
  • Many low density residential areas do not use an FSR for houses
  • Other rules often limit a house before it reaches the FSR

Where FSR comes from

FSR is a development standard set in a council's local environmental plan. It is usually shown on a map, with the ratio written as a number such as 0.5:1.

Not every zone has one. Many councils control house size through other rules, such as site coverage and landscaped area in the development control plan. Our guide to LEP vs DCP explains how the two work together.

What floor space ratio actually limits

FSR limits the total floor area of the building, in relation to the size of the lot.

A simple worked example

This example uses made up numbers only. If a lot is 500 square metres and the FSR is 0.5:1, the maximum floor area is 250 square metres. That is across all levels.

A single storey home could use all 250 square metres on the ground. A two storey home would split it between floors.

What counts as floor area

The LEP defines gross floor area. Some spaces may be counted and others excluded, such as certain basement areas or car parking. The exact list is in the LEP, so check its definition.

How to check the FSR for your property

  1. Find your lot and its council area
  2. Open the council's or the NSW planning online map and turn on the floor space ratio layer
  3. Read the ratio shown for your lot, if there is one
  4. Check the LEP clause and the definition of gross floor area
  5. Confirm with a planning certificate, or ask your drafter

If the map shows no FSR for your lot, your house is likely controlled by other rules. Do not assume there is no limit.

How FSR works with other controls

  • Height limit: caps how tall the building can be
  • Setbacks: decide how close walls can sit to boundaries
  • Site coverage and landscaped area: limit the footprint
  • Minimum lot size: affects whether you can subdivide
  • Heritage and flood controls: can reduce what is practical
FSR compared with other controls
ControlWhat it limitsWhere it usually sits
Floor space ratioTotal floor area across all levelsLEP
Height limitHow tall the building can beLEP, with detail in the DCP
Site coverageHow much of the lot the building coversDCP
SetbacksDistance from boundariesDCP
Minimum lot sizeWhether a lot can be subdivided or built onLEP

Our guide to height limits, setbacks and site coverage covers the other controls.

Common FSR mistakes

  • Assuming the FSR is the size you can build, when other controls may cut it down
  • Forgetting the height limit and storeys rule
  • Ignoring an odd site shape, a slope or an easement that reduces usable area
  • Counting only the ground floor, when all levels count
  • Assuming a space is excluded without checking the LEP definition
  • Using the lot size from the listing instead of the surveyed area

Does FSR apply to an existing house?

An existing house may already be above the current FSR, if the rules changed after it was built. That does not stop it standing.

But adding to it may need approval, and council may be less willing to add floor area to a house that is already over the limit. Your drafter can check before you commit.

How site constraints reduce what you can build

  • Flood or bushfire controls
  • Heritage listings and conservation areas
  • Trees, easements and sewer lines
  • Steep slopes and difficult access
  • Overshadowing and privacy rules

These can shrink the usable area well below the number the FSR suggests. Our guide to block suitability lists the main site checks.

The fastest way to check what you can build

Send us your address. We will read the LEP and DCP for your block, work out what you can build and quote a fixed fee for the drawings before any work begins.

Floor space ratio questions Sydney homeowners ask

How do I calculate floor space ratio?

Divide the total gross floor area of the building by the area of the lot. To find your limit, multiply the lot area by the FSR in the LEP.

Does every Sydney lot have an FSR?

No. Many low density areas do not use FSR for houses. They rely on other controls such as site coverage.

Does a garage count towards FSR?

It depends on the definition in your LEP. Some car parking is excluded and some is not. Check the definition.

Do upper floors count?

Yes. FSR counts floor area on every level.

Can I exceed the FSR?

Sometimes, through a formal request to vary the standard. It is harder than varying a DCP control, so most designs stay within the limit.

Is FSR the only thing that limits my house size?

No. Height, setbacks, site coverage, landscaping, privacy and site constraints all matter, and one of them is often the real limit.

Want to know how much you can build?

Send us your address. We will check the planning controls and quote a fixed fee for the drawings before any work begins.

Request a Fixed Fee Quote

0404 013 693 GET A QUOTE